Scenario:
Portland Enterprises recently completed merging with Lynaic Endeavors. The two Companies have been using separate routing protocols on their corporate networks, and an immediate solution is required for the two companies to begin sharing data. A boundary router, Amadiya has been established to perform mutual redistribution of route information between the two networks. Configure route redistribution from EIGRP into IS-IS and from IS-IS into EIGRP on the boundary router per the following requirements:
Seed metric for EIGRP must have the following characteristics :
Bandwidth = 512 kbps
Delay = 100
Reliability = 255
Load = 1
MTU = 1500
Seed metric for IS-IS must be set to 50.
Only redistribute Level-1 IS-IS routes into EIGRP.
Redistribute EIGRP routes into IS-IS as Level-1 routes.
Solution:
----------
Before we start to configure anything, we have to learn the Autonomous System (AS) number of EIGRP by using the show running-config on Amadiya router (remember you have to type cisco as its password to enter privileged mode)
Amadiya#sh run
From the output, we know that the AS number of EIGRP is 100, which we will use in the next commands.
Redistribute Level-1 IS-IS routes into EIGRP:
Amadiya#config t
Amadiya(config)#router eigrp 100
Amadiya(config-router)#redistribute isis level-1 metric 512 10 255 1 1500
Let's explain the last command redistribute isis level-1 metric 512 10 255 1 1500. To understand why we use these numbers, please see the structure of the above command:
redistribute isis {level-1 | level-1-2 | level-2} metric {bandwidth} {delay} {reliability} {load} {MTU}
{level-1 | level-1-2 | level-2}: because the question required we redistribute level-1 IS-IS into EIGRP so the easy decision here is level-1.
metric {bandwidth} {delay} {reliability} {load} {MTU}: From the question, we can identify:
Bandwidth = 512 kbps
Delay = 100
Reliability = 255
Load = 1
MTU = 1500
One thing you have to notice that if the delay is written without unit, we understand that its unit is microsecond. But in the "redistribution isis" command, the unit of delay is tens of microsecond. Therefore we have to divide the given number by 10, so the real delay we will use is: Delay (in redistribution command) = 100 (microseconds)/10 = 10 (tens of microseconds).
In the real exam, you might be given a delay parameter with unit, for example: Delay = 3ms then you have to change the unit to tens of microsecond. Delay = 3ms = 3000 microseconds = 300 tens of microseconds, therefore we have to use 300 for the delay parameter in the "redistribute isis ..." command.
Other parameters are normal and we can use them in the redistribution command without calculation.
ISIS, by default, does not advertise connected networks when redistributing into another routing protocol, so we have to use the redistribute connected command to advertise connected networks (of Amadiya router).
Amadiya(config-router)#redistribute connected
Redistribute EIGRP routes into IS-IS as Level-1 routes:
The question requires "the seed metric for IS-IS must be set to 50" so we just need to use a metric of 50 in the command
Amadiya(config-router)#exit
Amadiya(config)#router isis
Amadiya(config-router)#redistribute eigrp 100 level-1 metric 50
Amadiya(config-router)#end
Amadiya#copy run start
Don't forget to ping from Portland to Lynaic to make sure it works well!
.........................................................................................................................................
Saturday, August 22, 2009
Subscribe to:
Post Comments (Atom)
photos visible ah ve illa..enna da panreenga
ReplyDeletebeautifully explained. exactly what the exam calls for
ReplyDeleteHi Did anyone see this recently in their bsci exam?
ReplyDeleteBandwidth = 512 kbps
ReplyDeleteDelay = 100
Reliability = 255
Load = 1
MTU = 1500
Amadiya(config-router)#redistribute isis level-1 metric 512 10 255 1 1500
The delay variable be set to 100 not 10?
Delay (in redistribution command) = 100 (microseconds)/10 = 10 (tens of microseconds)
ReplyDeleteWhy not started in en command instead of conf t?
ReplyDeletewhy exit instead of end?